|
**Includes 1 extra glue bucket
HOMAG EDGETEQ S-240 FC AUTO Edgebander PDF
Stations:
- Pre-Milling Unit
- pre-trimming of the workpiece edge prior to gluing
- two (2) motors each 12,000 rpm
- one (1) motor clockwise rotation, one (1) motor counter-clockwise rotation
- vertical spindle adjustment via digital settings
- horizontal positioning via electro-pneumatic control
- dust extraction hood included with 120 mm diameter outlet
- diamond insert cutter heads, 100 mm diameter
- Automatic Magazine for Strip and Coil Feeding
- large coil table (800 mm diameter) with built-in rollers to allow for 3 mm PVC coils
- edge strip capacity: 4 - 6 mm
- direction of glue rollers reversible and glue roller section retractable
- one (1) large driven pressure roller with pneumatic pressure control
- two (2) secondary rollers, all with controlled side pressure
- manual setting of pressure zone via digital mechanical counter
- strengthened pre-cutter for cutting thick PVC edges from the coil; maximum 3 x 45 mm; precutting system equipped with air volume reservoir for on-demand activation required for short workpieces
- Hot Melt Gluing Unit
- quick purge feature to remove the glue and replace with different color or change to PUR glue
- Two level system: 350 g with 8-minute heat up time, 800 g with 15 minute heat up time.
- infrared radiant glue heat zone control for optimum gluing strength. Automatic temperature reduction if not run within 15 minutes. This feature reduces the temperature automatically by 50°C.
- Double-Motor End Trimming Unit
- straight/chamfer end trim unit equipped with two (2) 0.18 kW 12,000 rpm motors
- electronic motor brakes
- end trim unit utilizes drawing cut system for reduced blade projection when working on thick workpieces
- tooling also included
- program-controlled indexing from straight to bevel end trimming
- Straight/Radius Top & Bottom Trimmers
- equipped with two (2) 0.27 kW 12,000 rpm trimming motors
- electronic motor brakes
- program-controlled positioning when processing thin edge, thick PVC and solid wood edges; positioning done pneumatically via the EasyTouch controller
- horizontal and vertical tracing with lateral location indexing via digital "Quickset" system
- each trimming motor is equipped with one dust hood and dust extraction hose
- equipped with two (2) DFC combination straight / radius cutter heads, including four (4) carbide knife inserts with flush trimming possible up to 6 mm edge thickness
- nested top copy system
- Single-Motor Corner Rounding Unit
- corner rounding of thick PVC edging material
- includes diamond tooling
- Quick Change Profile Scraping Unit
- scraping of roughly trimmed thick PVC edges in order to remove the cutter marks
- vertical and horizontal tracing wheels
- radius knives included (quickly changeable to different radii)
- program-controlled indexing
- one (1) set of tooling standard
- one (1) set of tooling with nested top and bottom copy system
- Edging Scraper
- Quick Change
- Glue Scraper
- flat knives remove any unwanted material from the trimmed / scraped edge
- Buffing Unit
- two (2) 2,800 rpm buffing motors (one top, one bottom) for polishing of longitudinal edges
- inclinable vertically and horizontally
- two (2) buffing wheels included
Features:
Machine length: 4740 mm // 186.6 in.
Feed speed: 11 m/min // 36 ft./min
Workpiece width (in case of thickness 8 - 22 mm): 70 mm // 2.8 in.
Workpiece thickness: 8 - 60 mm // 0.3 - 2.4 in.
Edge thickness coils: 0.3 - 3 mm // 0.012 - 0.12 in.
Edge thickness strips / solid strips: 0.4 - 6 mm // 0.016 - 0.24 in.
Voltage: 400Y / 230 volts
Phase: 3
Frequency: 60 Hz
Full load current: 17.9 amps
Short circuit current rating: 5 kA rms symmetrical
Control voltage: 24 volts
Largest motor: 4.6 amps
Enclosure type: 1
Largest heater: 2.3 amps
|
